Skip to product information
1 of 14

iFlight

iFlight BOB57 Cinematic LR & Freestyle 6inch w/Nebula Pro Vista - BNF

iFlight BOB57 Cinematic LR & Freestyle 6inch w/Nebula Pro Vista - BNF

Regular price CHF 319.99
Regular price CHF 599.00 Sale price CHF 319.99
Sale Sold out
Tax included. Shipping calculated at checkout.
Receiver Options (match your Remote Control)

About the Product

The pilot & videographer Ellisvanjason and iFlight teamed up to craft the BOB57 FPV Drone: a cinematic 6-inch drone that ensures agility and flight time and therefore combines the advantages of both 5-inch and 7-inch quads. 

Features

  • 6-inch drone re-engineered: This drone was specifically designed for 6 inch
  • H-shaped frame with robust middle section for less props in view while remaining stiffness
  • XT60 front-mount: Compare to other drones the mount sits in the front and gives more space on the back.
  • Built in BEC to directly power a gopro (no battery needed)
  • Hybrid motor design: This motor is optimized for 6-inch.  Can be used with bi- blades (efficiency) and tri-blades (agility & trust). 
  • Antenna mount: Solid antenna mount for less oscillations when using long antennas
  • Long back bone: Enough space up to 3000mAh 6S batteries
  • Gladiator shell: Protection shell from dust and water droplets (shall be removed for max. flight time)
  • GPS: A high-end GPS is used to minimize the risk of failure during proximity flights 
  • ESC: The drone comes with iFlight's new ESCs with built-in spike absorber for more reliability
  • Pre-tuned by Ellisvanjason

Battery recommendation

Accessories

  • Gemfan 6032 Tri-Blade Propeller designed specifically for the BOB57

Specifications

  • Upper (middle) plate thickness: 2.5mm
  • Bottom plate thickness: 1.5mm 
  • Total Dimensions: 254*254mm 
  • Bottom to top distance: 22mm 
  • Geometry: H-shaped frame
  • Top plate thickness: 2mm 
  • Ellisvanjason 2506 motors 
  • Gemfan 6032 propellers
  • Arm Thickness: 6mm

Electronics

  • ESC: BLITZ F7 Stack (F7 V1.1 + 55A 4in1 ESC)
  • FC: BLITZ F722 Flight Controller
  • Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter
  • Smartaudio / IRC Tramp VTX protocol supported
  • Firmware target: iFLIGHT_BLITZ_F722
  • Motor outputs: 4x (SH1.0 connector)
  • Flash: 32MB (Blackbox flash)
  • I2C serial: SDA / SLA pads
  • Dimensions: 36.5*35 mm
  • Barometer: DPS310
  • OSD Chip: AT7456E
  • LED controller: Yes
  • MCU: STM32 F722
  • Beeper pad: Yes
  • Gyro: BMI270
  • Weight: 7.8g
  • UARTS: 6

ESC 

  • BLITZ E55 4-IN-1 2-6S 55A ESC
  • Supports: DShot DShot150/300/600/MultiShot/OneShot etc.
  • Mounting Holes: 30.5*30.5mm/Φ4mm
  • Target:   IFLIGHT_BLITZ_G2
  • Supports 2-6S Lipo input
  • Current sensor: Yes
  • Constant: 55 Amps 
  • Current rate: 200
  • Burst: 65 Amps
  • Weight: 15.3g
  • MCU:G071
  • BEC: No

Contains

  • 1 x Pre-built and Tested BOB57
  • 2 x GEMFAN 6032- CW propeller + 2 x  6032 CCW (Green)
  • 2 x GEMFAN 6032- CW propeller + 2 x  6032 CCW (Black)
  • 1 x Albatross LHCP 5.8GHz SMA FPV Antenna 150mm
  • 1 x Albatross LHCP 5.8GHz SMA FPV Antenna 60mm
  • 1 x USB Type-C 5V Balance Plug Power Cable 55mm
  • 2 x iFlight Lipo Strap 20*250mm (Black)
  • 1 x Nebula Pro Vista HD System

Note

All iFlight BNFs are tested before shipment to guarantee the highest quality. 

If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.

iFlight takes no responsibility for issues with DJI or Caddx 3rd party gear (Video transmitters, Goggles, Radios, etc) and must be directly reported to caddxfpv.com/pages/contact-us or www.dji.com/support

View full details